Day One - Discussion Topics

Aug 26, 2012 1 HP vs 3/4 HP submersible pump, flow rates, H2O pressure, differences? Happened while running it during the course of the first week when we were trying to clear out the dirty water from the well pump exchange of contractors to our pump. Have since learned Flotec is junk for well pumps. Well guy came out again and developed the well. NOTE: For proper performance, pump MUST be matched to ejector and to well depth. Use shallow well installation for wells up to 25 ft depth to water and deep well ejector for depths up to 130 ft. Long runs and many fittings increase friction and reduce flow. Locate pump as close to well as possible: use as few elbows and fittings as.

A quartz wall clock is made up of a battery, a microchip circuit, an electric motor, gears, hands, a clock face and, of course, a quartz crystal. To get things started, the battery sends an electric current to the circuit board, which creates pressure on the quartz, causing it to vibrate. Jun 28, 2013 Discussions. Archive Collectibles. Staiger Clock - where can I get a replacement cloc. Subscribe to RSS Feed. Mark Topic as New. Mark Topic as Read. Float this Topic for Current User. Samsung Galaxy Y Duos Gt S6102 User Manual Pdf Baofeng Uv 3r Plus User Manual Cisco Isb7005 Box User Manual Pdf Users Manual Staiger Quartz Clock Replace Battery Mercedes Benz Gl450 2007 User Manual Xeonon Bulb Canon Lide 210 User Manual Pdf Samsung Led Tv Series 5000 User Manual Cytoscape 3.6.0 User Manual.

Centrifugal Pump Design Download saac 2 64 bit.

• A Short History
• Bernoulli’s Principle & the Venturi Effect
• Centrifugal Pump Design

Pump Parts and Identification – Hands-On Activities

• Wetted End Parts
• Dry End Part
• Pump Tree
• Drivers
• How to Read a Cross-Sectional View

Bearing Removal and Installation

• Bearing Types and Identification
• Expected Life Based on Bearing Loads and Speeds
• Proper Installation of Pump Bearings
• How to Use Micrometers – Hands-on Exercise
• Press Fitting
• Thermal Installation
• Lubrication of Pump Bearings

Bearing Failure Analysis

• Disassembling a Bearing for Inspection
• Troubleshooting Bearing Failures

Simple Vibration Measurement

• History of Vibration as a Condition Testing Tool
• How to Read a Vibration Meter
• Measurement of Vibration Velocity
• Troubleshooting Using a Vibration Meter

Acoustical Measurement of Pump Bearing Condition

Users Manual Staiger Quartz Clock Replace Battery Replacement

User Manual For Leo Deep Well Pump Ajdm75 4h Test

• Introduction to Acoustical MeasurementsSpalling and How to Determine When It Occurs
• Pump Bearings Condition Guide

Split Case Pump Rebuilding Techniques

• Techniques for Rebuilding a Spit Case Horizontal Pump
• Techniques for Rebuilding an ANSI Frame Back Pull-Out Pump

Submersible Deep Well Pump

Pump Foundations

Red Jacket Deep Well Pump

• Anchoring, Shimming & Grouting

Staiger Quartz Clock Movement

User Manual For Leo Deep Well Pump Ajdm75 4h Club

User's Manual Staiger Quartz Clock Replace Battery Replacement

Staiger Quartz Clock Insert

Pump Shafting Inspection and Repair

Deep Well Pump Diagram

• Shaft Condition & Drawings
• Stub Shaft Techniques
• Bowed Shafts
• Diameter Corrections

How do I set a Radio controlled clock?
Make sure when setting your clock that it is away from any electrical equipment such as computer, TV etc. A window sill is an ideal place to set it, as this is often where the strongest signal is found. The time signal cannot be transmitted through metal such as radiators.

Analogue Clock

When the battery is inserted the hands will travel to either 12, 4 or 8 o’clock and stop while it searches for the time signal. Depending on the strength of the signal, this can take a couple of minutes or a couple of hours. Once found the hands will travel to the correct time and depending on which model of clock, it will check the signal several times a day to ensure correct timekeeping.
The signal is always strongest between 2am and 6am, so sometimes it might be necessary to leave your clock overnight to find the signal in low signal areas.

Digital clock

Whatever make of radio controlled digital clock you have they all basically set themselves in the same way. When you insert the batteries the display will show at the default time and date, often 1 January 12pm. The time will start until it finds the signal and it will start flashing the correct time. The strength of the signal is normally shown with a symbol as shown below.

Below are some instructions for setting digital clocks including Radio Controlled models

Click on the thumnail to open a PDF file

London Clock Co Instruction Manuals

Precision Clocks Instruction Manuals

Seiko Clock Instructions